TPFanControl 0.63准绿色版+教程

显示全部楼层 · 发表于 2014-2-28 10:41

TPFanControl绿色版完全从安装版绿化而来,决不添加任何流氓插件等.

解压缩后,可以放入任何文件夹内,然后运行!)Green.bat一下,完成绿化,如果怕的话,可以手动将TVicPort.sys拷入c:\windows\system32\drivers完成绿化

之后就可以双击TPFanControl.exe运行了,其中TPFanControl-0.62.exe是0.62版的,经MD5检查,0.62版和0.63版只有这一个文件有区别.

ini配置文件是我自己重新定义的,大家可以自行修改,搜索MenuLabelSM1=Smart Mode 1,然后下面的温度自己调.
为了方便大家阅读,把配置的内容贴在下面了,配合浅显易懂的中文翻译,纯手工翻译!!非直译,其中(* *)中间的注释是我本人的注释,非翻译.有什么不懂可以回帖

// !!! Temp of lowest Level > 79 -> switch to Fahrenheit !!! see below
// 最低一级的温度值如果>79的话,则温度自动识别为华氏度.

// ATTENTION: example temp values are for my T61, especially
//BluetoothEDR=1, SensorName5=no5, IgnoreSensors=no5 too
// temp levels 10 degrees centgrade higher than in T4x, R5x,
// change for your purposes.
// 注意,下面的温度设置是以我的T61为例,特别是蓝牙EDR设置为1,第五个传感器名称改为no5,并且忽略这个传感器的温度显示.在T4X,R5X机器上,温度设置要高个10°,总之以你自己实测的效果来调试.

TPFanControl.rar (297.06 KB, 下载次数: 11252)

2014-2-28 10:41 上传

点击文件名下载附件

// advice for programmers: TPFanControl must acquire mutex named
// "Access_Thinkpad_EC" to get access to embedded controller
// 建议: TPFanControl必须获得"Access_Thinkpad_EC"才能得到温度值.

// with Active=3 & ManFanSpeed=0 & ManModeExit=78 you can have a nice
// quiet time until temps reaches 78 deg. centigrade  :-))
// 当使用手动模式(Active=3),风速为0(ManFanSpeed=0),并且将"手动切换到智能的温度阀值"设定为78°(ManModeExit=78)的话,你的电脑将会异常安静,除非温度攀升到78°.

// -----------------------------------------------------------------
// -----------------------------------------------------------------
// "Active=0" program just reads config. 程序仅读取配置
// "Active=1" allow program to modify fan. 允许程序修改风速
// "Active=2" program will come up in smart mode. 程序以智能模式启动
// "Active=3" program will come up in manual mode. 程序以手动模式启动

Active=2

// -----------------------------------------------------------------
// manual fan speed at program start
// 程序启动时,手动风速的初始值.(*我发现我的T61上,64风速是最快的*)

ManFanSpeed=64

// -----------------------------------------------------------------
// Program exits manual mode and switches to smart mode with last chosen
// profile, if this temp (degrees Centigrade or Fahrenheit) is achieved.
// default= 80 degrees Centigrade / 176 degrees Fahrenheit.
// 当温度达到该值时,程序将自动退出手动模式,并切换到之前启用过的智能模式.

ManModeExit=78    //ManModeExit=172 // with Fahrenheit

// -----------------------------------------------------------------
// Window stays on Top if StayOnTop=1, normal behavior =0
// 窗口是否一直前置显示,1为前置,默认为0,不前置.

StayOnTop=0

// -----------------------------------------------------------------
// Set to 1 for slim widget
// 1为窗口细长型显示,0为窗口粗矮型显示,显示的信息量相应的多一些.

SlimDialog=1

// -----------------------------------------------------------------
// set to 1 for bluetooth with enhanced data rate (i.e. T61,
// X61  for T4x, R5x set BluetoothEDR=0 )
// 设置为1时增强蓝牙的传输速率,例如T61,X61.但是对于T4x,R5x,请设置为0

BluetoothEDR=1

// -----------------------------------------------------------------
// Windows Priority of Process (0-5, normal=2), increase if fancontrol has
// big delays in response while other processes consume performance.
// 程序的优先级,可以设定为0-5,正常是2,如果其他程序大量消耗系统资源导致TPFanControl有较大的延迟,请把这个数值加大.

ProcessPriority=5

// -----------------------------------------------------------------
// Show no icon ballons: NoBallons=1, show icon ballons: NoBallons=0
// 禁止托盘处的程序图标显示提示信息时,设为1,反之设为0.

NoBallons=1

// -----------------------------------------------------------------
// check temperatures every x seconds (default 5)
// 每隔x秒检查温度,默认是5.

Cycle=1

// -----------------------------------------------------------------
// For Thinkpads A2x,T2x,X2x set NoExtSensor=1 to exclude reading
// of extended sensors to prevent program errors. Attention 570(E)
// is NOT compatible. Fan speed is not available on all models.
// 对于Thinkpad A2x,T2x,X2x,设为1可以避免因读取不存在的温度传感器而导致程序出错.注意,570(E)是不兼容的.所有的机型上都无法设定风速.

NoExtSensor=0

// -----------------------------------------------------------------
// Minimize to systray immediately when starting
// 设定为1时,当程序启动后,立即最小化到托盘.

StartMinimized=1

// -----------------------------------------------------------------
// check icon of tpfcicon.exe (optional) every x seconds (default 1)
// 每x秒检查tpfcicon.exe的图标(可选,默认是1秒).

IconCycle=1

// -----------------------------------------------------------------
// Show new icon with max. temperature / sensor name
// 显示最高的温度和芯片的名称

ShowTempIcon=1

// -----------------------------------------------------------------
// Save the icon by a start delay of the program/service of
// "SecStartDelay" (sec.) within "SecWinUptime" (sec.) after (re)boot
// Delete slashes '//' at next 3 parameters.
// 在启动或重启后,设定程序的延时启动时间,将下面的'//'删掉就能启用(*这个没啥用,我不弄的*)

//SecWinUptime=120       //"SecWinUptime" (sec.) after (re)boot
//SecStartDelay=60       //start delay of the program (sec.)
//NoWaitMessage=0       //set to 1 to avoid sleep message
//ReIcCycle=600             //rebuild TempIcon every xxx secs.

// -----------------------------------------------------------------
// Temperature thresholds for turning the taskbar icon
// yellow orange red (Smart and Manual mode only and
// only together with MinimizeToTray=1)
// 对于不同的温度,系统托盘所显示的颜色,黄,橙,红.仅在智能和手动模式下生效,并且MinimizeToTray=1

IconLevels=50 60 65 // Fahrenheit: IconLevels=122 140 158

// -----------------------------------------------------------------
// Beep frequency and duration (in ms) for successful
// fan state changes. (Set either or both to zero to
// disable)
// 当成功转换风扇状态时,蜂鸣器的频率和时长(毫秒),任何一个值设定为0时,禁止蜂鸣.

FanBeep=0 0

// --------------------------------------------------------
// If this max number of consecutive EC read errors occur
// program will switch fan back to bios mode and exit
// 当读取温度传感器的错误次数达到改设定值后,程序将自动切换到bios控制并退出.

MaxReadErrors= 10

// --------------------------------------------------------
// Log2File=1 enables, Log2File=0 disables writing to TPFanControl.log
// Start program with admin rights.
// 允许或禁止写入日志文件,这个需要管理员权限

Log2File=0

// --------------------------------------------------------
// Log2csv=1 enables, Log2csv=0 disables
// writing to TPFanControl_csv.txt renamed to
// TPFanControl_last_csv.txt after restart of TPFanControl
// rename to *.csv for use with excel
// Start program with admin rights.
// 设定为1时,允许日志写入TPFanControl_csv.txt,程序重启后,自动更名为TPFanControl_last_csv.txt.将扩展名改成.csv时,可以用excel打开.(*这个需要在文件夹选项中,将"隐藏已知类型的扩展名"后面的勾去掉才能显示并更改扩展名*)

Log2csv=0

// --------------------------------------------------------
// List (separated by comma) of sensors to ignore when
// determining the max. temperature.  (Use lower case,
// e.g "IgnoreSensors=pci,aps")
// 判断最高温度时,哪些芯片是不受监控的(相当于黑名单,多个名称用逗号隔开,并用小写字母).

IgnoreSensors=cpu,aps,crd,bat,bus,pci,pwr
// (*我的T61有显卡门,所以只监控gpu的温度,除了gpu,其他所有的芯片都列上去了.大家可以把cpu从黑名单中删除*)

// ---------------------------------------------------------
// List of new 3 letter sensor names, delete leading
// slashes to activate. Don't use capital letters for readability
// of temp icon.
// 写3个新的字母来重新命名芯片的名称,把'//'删除就能启用.别用大写字母

//SensorName1=cpu
//SensorName2=aps
//SensorName3=pcm
//SensorName4=gpu
//SensorName5=no5
//SensorName6=x7d
//SensorName7=bat
//SensorName8=x7f
//SensorName9=bus
//SensorName10=pci
//SensorName11=pwr
//SensorName12=xc3

// ---------------------------------------------------------
// calculating Highest Temp with:
// temperature of sensor no. = real temp minus SensorOffsetno.
// Default SensorOffset1-12=0 , Capital O in SensorOffset,
// to activate delete slashes '//',
// Negative SensorOffsetno. values increase temperature values.
// 重新计算最高温度,传感器温度=实测温度-偏移量,默认的偏移量都为0,删除'//'可以启用计算.当偏移量为负数时,则增大温度值

//SensorOffset1=20
//SensorOffset2=20
//SensorOffset3=0
//SensorOffset4=2
//SensorOffset5=1
//SensorOffset6=5
//SensorOffset7=5
//SensorOffset8=4
//SensorOffset9=3
//SensorOffset10=2
//SensorOffset11=1
//SensorOffset12=5

// -----------------------------------------------------------------
// set to 1 to show calculated temps for sensors
// 设定为1时,显示计算后的温度值

ShowBiasedTemps=1

// -----------------------------------------------------------------
// Show all/active sensors at start up. all=1 only active=0
// 在启动时,显示所有/激活的传感器温度值,1为所有,0为激活的

ShowAll=0

// --------------------------------------------------------
// temperature levels 'Level=' with associated fan levels
// (for the fan to come back, temperature must fall
// down to previous level).  There may be more or
// less levels in this list.  The first one should
// have a fan speed of zero and is the "turn off"
// temperature.
// Fan speed of 64 is extreme and may be an *unsupported*
// and *damaging* mode.  A fan speed of 128 setting is
// not really a fan speed in itself but will instead switch
// fan control to BIOS mode (0x80).  The idea of this
// is to let the program get out of the way and let the
// BIOS handle extremes.(and then switch back to smart if
// the temperature is okay again)

// Temp of lowest Level (commonly set to fan speed zero) of profile
// "Smart Mode 1" will switch from Celsius to Fahrenheit if set higher
// than 79 degrees. Temps of higher levels have no influence on F/C.
//
// profile "Smart Mode 1"
// change values and number of items for your needs
// Celsius:                // Fahrenheit:

MenuLabelSM1=Smart Mode 1/  Label for Icon Menu, must be terminated by '/'

Level=30 0             // Level=140 0
Level=40 1             // Level=150 1
Level=45 4             // Level=165 3
Level=49 7             // Level=175 7
Level=52 64             // Level=195 64

// (*这些是我的温度设定,分别设定了30°,40°,45°,49°,52°,可以自己改*)

// optional 2nd profile "Smart Mode 2", switched by icon menue
// change values and number of items for your needs
// to deactivate, insert leading '//' into following lines

MenuLabelSM2=Smart Mode 2/  Label for Icon Menu, must be terminated by '/'
// (*智能模式2下的设定*)

Level2=30 0             // Level=140 0
Level2=40 1             // Level=150 1
Level2=45 4          // Level=165 3
Level2=49 7             // Level=175 7
Level2=52 64             // Level=195 64

// -----------------------------------------------------------------
// IconColorFan=1 digital Icon will turn green while fan is running.
// 设定为1时,当风扇转的时候,图标为绿色

IconColorFan=1

// -----------------------------------------------------------------
// Lev64Norm=1 : Fan level 64 acts as normal level with hysteresis,
// fan will run till next lower temp step is reached (no pulsing fan).
// If set to zero fan level 64 acts as emergency level without hysteresis,
// fan will run till level64 temp is reached again (pulsing fan can happen).
// 设定为1时,最高风速有延迟效应,也就是说,当温度下降到最高档温度值以下时,风速仍旧为最高,直到继续下降到下一档温度时,才调低到下一档风速.如果设置为0,则一旦下降到最高档温度以下时,就立马降低到下一档风速,直到温度再次超过最高档温度值时再调高到最高风速.

Lev64Norm=1